So many of you loved the giant flowers from Britney + Marks wedding that we asked Britney to share how she made those huge flowers and we are super excited to share the DIY with you all today! Britney did want me to share a little disclaimer that when they made these they never planned on creating a tutorial (but we are so happy you did!), so there is no exact science just do what works for you, and if you have a great solution for one of the steps please share it! Big thanks to (once like a spark) photography for the photos!
Materials:
Several sheets of poster board (it takes at least two full sheets of poster board per flower)
Large Plastic Solo Cups (1 per flower)
Bath poof
Hot glue gun and extra sticks
Spray Paint
Clear Plastic Wrap
Thin wall electrical conduit, ½ x 10. Home Depot SKU# 203106
Halex ½ set screw connectors, Home Depot SKU# 839663
Raco 3 ½ round cover, Home Depot Internet SKU# 202058390
Wood Block or bucket filled with sand to help the flower stand up
Fabric to pool at the base of your stems
Preparing the bath poof:
So we tried to use a whole poofbut it was just too much, so we cut it in half. There is a small rope that goes around the middle of the bath poof. Cut the poof in half leaving one side tied up by the rope. Keep a firm grasp on the rest of the poof. Add a generous amount of glue to the newly cut edge, then cover with a scrap of poster. Re-glue any places that are not secured. Do the same to the other half. Now you can make two flowers. Yay!
MAKING THE FLOWER
Step one:
Lay the poster board glossy side down. (If the poster does not have a glossy side, its just fine.) Rip the poster towards yourself length-wise. Start by ripping pieces that are the entire length of the poster. Im not going to lie, it takes a little practice to get a good technique.
After you get 5-7 very long petals between 2-4 inches wide, move on to tearing the smaller pieces. Its good for the petals to curl, because they will begin to flatten out over time and you dont want a droopy flower.or maybe you do!
Tip: Separate the petals based on size. You need several of each size, but more ofthe medium and small.
Step Two:
Cut your cup in half. Then cut 1 inch tabs all the way around it. This will be your base. Hot glue your biggest petals to the OUTSIDE of the cut tabs. The weight of the petals should open the cup into a semi-flat shape.
Step Three:
Continue adding petals to the INSIDE of the cup moving from largest to smallest. Be sure to fill in areas that look empty. Stop before you get to the smallest petals.
Step Four:
Glue your bath poof to the center. Once the bath poof is glued, add the smaller petals so that they curve up around it.
Step Five:
Once you are satisfied with the fullness of the flower, lightly dust the center with spray paint.
Tip:Guard the outer petals with newspaper or extra poster so they dont get sprayed.
Preparing the stem:
Im going to be honest, my dad did this part and there is no exact technique. Some have asked if PVC pipe would work. We tried it, but it was too flimsy. Instead, we used thin wall electrical conduit from the electrical department at Home Depot. You also need a screw connector and a round metal outlet cover. If you are confused, print out the picture, take it to the home improvement store and they should know exactly what you need.
Bending the conduit (stem). THIS is the difficult part: Hold the pipe up at an angle, one end resting on the ground. Slightly bend by stepping on the lowest section, move your foot up 8-10 and repeat until you have the curve you want. Be careful and dont try to bend the conduit all at once, making numerous smaller bends works best. Once the conduit is curved, attach the Halex screw connector onto the flower end of the conduit, knock the center plug out of the Raco round cover plate and secure it to the screw connector (very easy, just sounds confusing).
Option 1: Drill a 7/8 inch hole in a large piece of wood. Insert the bent conduit stem (as seen below).
Option 2: Use buckets filled with gravel or sand to keep the flower upright.
Option 3: Simply push the stem into the ground if your event is outdoors.
Option 4: Make something up. If it works, share your wisdom with the rest of us!
Wrap the conduit in several layers of clear plastic wrap. It actually looks better if its a little messy.
Finally, attach the completed flower using a lot of hot glue to the 3 ½ cover plate. You will need A LOT of hot glue. And just when you think it is secure, add more gluejust in case. You dont want the wind taking off with the top of your flower! Now pool your fabric around the base (you can see this in her ceremony photos below) and Viola! You are finished!!
And a few photos from their wedding to see how they used them for their pretty outdoor ceremony be sure to check out their entire wedding feature here!
Big thanks to Britney for putting this together for us and to (once like a spark) photography for the photos!
So many of you loved the giant flowers from Britney + Marks wedding that we asked Britney to share how she made those huge flowers and we are super excited to
DIY: Giant Paper Rose Green Wedding Shoes | Apartment ...
My best friend has had two oversized crepe paper flowers for years that I have always coveted. They've moved with her from house to house and are always displayed in
1000+ ideas about wedding DIY on Pinterest | Green Wedding ...
Diy Boutonniere Wedding, Felt Flowers, Green Wedding, Diy Floral, perfect for a bridal shower, DIY: (Green Wedding Shoes) DIY Giant Moon Backdrop,
DIY Giant Paper Rose Paper Bridal Bouquet -Green Wedding ...
Explore stunning DIY Giant Paper Rose Paper Bridal Bouquet -Green Wedding Shoes wedding images to help inspire and plan your perfect day.
Giant Paper Flowers | Green Wedding Shoes ... | Scissors ...
Giant Paper Flowers | Green Wedding Shoes Normally I would think that giant paper flowers were super tacky but I Scissors & Thread is a creative mix of DIY
DIY: Giant Paper Rose Flower | Green Wedding Shoes ...
DIY: Giant Paper Rose Flower. If you loved the beautiful DIY wedding this morning and Natas gorgeous paper flower bouquets, you are in luck as Nata is sharing
DIY Giant Paper Rose Flowers from Green Wedding Shoes ...
The site, Green Wedding Shoes, even provides a tutorial entitled, DIY Giant Paper Rose Flowers. DIY Giant Paper Rose Flowers from Green Wedding Shoes
Green Wedding Shoes on Pinterest
Green Wedding Shoes wedding DIY Green Wedding Shoes 347 Follow bridal shower ideas Green Wedding Shoes 109 Follow
DIY Peony Bouquet | Green Wedding Shoes | Afloral.com
Follow along with Green Wedding Shoes and create your own peony bridal bouquet with real touch faux flowers from diy peony bouquet, green wedding shoes,
DIY Giant Paper Rose Flower - CraftSmile
DIY Giant Paper Rose Flower . From Greenweddingshoes.com. Posted by Christine Taylor
